1.20 RC AIRPLANE DRASTIK

DRASTIK 120/ 20-28CC 78" WING SPAN  (video) (in stock )
DRASTIK 120/ 20-28CC 78" WING SPAN (video) (in stock )
Item# 8030C-R
$349.95
Availability: Usually ships the next business day

Product Description

HAS FLAPS, 2 PEICE WING AND YOUR CHOICE OF TAIL DRAGGER OR TRICYCLE GEAR (ALL INCLUDED IN BOX)

OVER SIZE SHIPPING. 57X21X12 BOX SIZE SHIPS AS 68 LBS. DIMENTAL WGT.

WE HAVE THIS PLANE IN ALL 3 COLORS THAT ARE LISTED FOR STICK AIRPLANES. PUT THE COLOR DOWN ON THE COMMENT LINE WHEN YOU ORDER. WE WILL POST NEW STOCK NUMBERS FOR COLORS NEXT WEEK.

New item for 2013. (OVER SIZE SHIPPING AND DOUBLE BOXED) 57 x 21 12. We have the factory double box (or crate) our planes and they do an over-kill which makes the freight higher because of box size. But who want a busted plane and try to collect from the fgt. carrier?

This is an ARF and not a kit. Comes with complete hardware kit that includes- 3" foam wheels' fuel tank alum. landing gear that attaches with 3 screws, spinner, pushrods, tail wheel, etc.

Details are as follows:

Fuselage- Lite ply construction with lighting holes to save weight, Servo tray is installed and is located under the wing (1 servo for throttle, 1 servo for rudder ). Rudder is pull-pull system and only requires 1 servo. Requires 2 servos for the elevator halves and are mounted in the outside of the fuselage near and below the elevator halves. Firewall measures 4 1/2" wide and 5" tall. Landing gear attaches 7" back from firewall and uses 4 screws. Fuselage has a hatch located between wing and firewall with a spring loaded latch that lets you service the fuel tank (or batteries if you are using electric power)

Wing- 2 1/2 inches thick, 18 1/4" cord, symmetrical design, built up balsa design. has alum. wing tube joiner to make a 2 piece wing for easy transport.. Uses 2 aileron (1 under each wing half). Ailerons are 28 1/4" by 3 3/4" each. Uses 2 flap servos.

Tail Feathers - Flat (no airfoil and epoxies to fuselage) 10 1/8" cord including elevator halves. Horizontal stab. is 23 1/2" on leading edge tapering to 29 1/4" at rear (with elevator halves installed). Elevator halves are 11" by 4" each. Vertical stab. is 10 1/4" tall and 11" long tapering to 3 inches at the top (rudder not included). Rudder is 11 1/2" tall. Rudder is 5 inches at the bottom tapering to 2 1/5 inches at the top.

Recommended Throws- 45 deg. (up and down) for all surfaces

Plane weighs 7 lb. 3oz. with all hardware

Wingspan: 78 inches

Wingarea: 1349 sq. in.

Length: 68 inches

Engine: 2C 1.20 cu.in;26cc gas engine

Radio: 5 Channels; 8 Servos





Email and video from customer: Use full screen and turn the volume up. 118 mph mid-air colision at vety end of short video.

We put the Drastick together with the DLE 35 RA. It is a speed demon. Crow flaps worked really well. I made a few low passes across the field at 118 MPH.

We were fine tuning the engine and had the field to ourselves as everyone was giving us the space we needed to make low passes to test the prop and engine setup. A friend of mine was taking video with his IPhone. We werenít ready to start filming with our cameras yet as I had a few tweaks I needed to make.

Some dumb Axxxx (without calling out he was taking off) took off with an electric foam P-38. We didnít even know he was in the air. I started to make a high speed low pass and the engine coughed a couple of times. As the plane was about mid field I banked it left to come around and land to tweak the needles a little bit. When I banked left I hit this P-38 square in the middle of the of its wings right on the nose cone of the Drastick. This was the second flight right after the maiden. The P-38 evaporated. The Drastick was paralyzed because the collision cut all power to the receiver. When we got to the crash site we couldnít find any P-38 parts and do you know why? The twin electric motors, speed controllers, servos, receiver, props, and batteries were in the fuselage and wing of the Drastick. The collision didnít hurt the Drastick beyond repair but it went in nose first because I had no control of the servos.

Here is the video of the collision. Again, this was only taken with his iPhone and not intended as the video for the plane. He had just stopped recording because I was coming around to land but he got the collision right before the camera turned off.

Accessories

ARF PITTS EP
ARF PITTS S 12 BI-PLANE, PRE-COVERED WITH OUR LIGHT BUT STRONG) PREMIUM POLYESTER HEAT SHRINK COVERING. FEATURES A MAGNET HELD HATCH THAT THE CANOPY IS PRE-INSTALLED INTO. THE HATCH OPENS FROM BEHING THE CANOPY, ALL THE WAY TO THE COWL FOR AMPLE BATTERY AND SERVO ACCESS.

THE COWL AND WHEEL PANTS ARE MADE FROM FLEXABLE MOLDED HIGH IMPACT PLASTIC THAT IS STRONGER AND MORE FLEXABLE THAN THE NORMAL HARD PLASTIC THAT YOU GET WITH MOST ARF'S.

THIS ARF IS 90% PRE-BUILT AT THE FACTORY, AND INCLUDES A COMPLETE HARDWARE KIT.

WINGS AND FUSELAGE ARE ALL BUILT UP WOOD AND LITE PLY. FEATURES A JIG BUILT ONE PEICE WING SYSTEM TO INSURE GOOD FLIGHTS AND NO ULGY GLUE JOINTS.

ALUM. LANDING GEAR.

WING SPAN.............35.4"

WEIGHT WITH ALL HARDWARE............1LB. 12 OZ.

WING AREA............................390 SQ. IN.(thanks for the up-date Gary)

LENGTH...............................34.6 IN.

REQUIRES OUTRUNNER BRUSHLESS MOTOR, 2100/2500MAH LI-POL BATTERY, 25-30A SPEED CONTROLLER........(OR EQUIV.)

REQUIRES 4 CHANNEL, WITH 4 MINI SERVOS- RADIO.





$149.00
Availability: Usually ships the next business day
ARF PITTS EP 8126
$10: 
This item is currently out of stock!